Pharma Tips

Granulation & Particle-Bonding Mechanism Process

By: Pharma Tips | Views: 3322 | Date: 31-Aug-2015

All about Granulation including Reasons for granulation, Bonding mechanisms between particles, Mechanisms of granule formation and methods for granulation.

Granulation & Particle-Bonding Mechanism Process

What is Granulation?

Granulation is the process in which powder particles are made to adhere to form agglomerates called granules.

Why Granulation?

To prevent segregation of the constituents of the mix.
To improve the flow properties of the mix.
To change the particle size distribution so as to improve the compressibility and to increase apparent density of the powder.

Reasons for granulation are:
lGranulation of toxic material reduce the hazard associated with handling of toxic dust. Granulation should be non-friable & have suitable mechanical strength.
lFor slightly hygroscopic material granulation reduces possibility of caking. As granules can absorb more moisture yet retain their flow ability because of their size.
lGranules being compact than the powder occupy lesser volume per unit weight therefore they are more convenient for storage and shipment.

Bonding mechanisms between particles:

1. Adhesion and cohesion forces in the immobile liquid films between individual primary powder particles.
2. Interfacial forces in mobile liquid films within the granules;    
3. The formation of solid bridges after solvent evaporation;
4. Attractive forces between solid particles;
5. Mechanical interlocking.
6. Granulation can improve or modify drug release profile.

Mechanisms of granule formation:

In the dry granulation methods, particle adhesion takes place because of compaction forces. A compact or sheet is produced which is larger than the granule size required, and therefore the required size can attained by milling and sieving.

In subsequent wet granulation methods, binder added to dry powders has to be distributed through out  the powder by  the mechanical agitation created in the granulator. The particles adhere to each other because of binder, and further kneading causes more particles to adhere. The precise mechanism by which a dry powder is transformed into a bed of granules varies for each type of granulation.

Nucleation: Granulation starts with particle to particle contact and adhesion due to liquid bridges. Number of particles will join to form the pendular state.

Transition: Nuclei can grow in two possible ways either single particles can be added to the nuclei by pendular bridges, or two or more nuclei may combine. The combined nuclei will be reshaped by the agitation of the bed.

Ball growth: Granule growth produces large, spherical granules and the mean particle size of the granulating system will increase with time and agitation.

Chopping: Bigger size are granules are chopped to smaller granules in the process of ball growth. Chopping is repeated to achieve the granulation end point.

Granulation and Particle-Bonding Mechanism of Granulation


Particle-Bonding Mechanism

There are two methods for granulation:
1.Wet granulation method:  In this granulation binder solution is used.
2.Dry Granulation:  Granulation is achieved with the help of mechanical compaction or force.


To form granules, a strong bonds must be formed between powder particles so that they adhere not easily breakdown in subsequent handling operations.

There are five primary bonding mechanisms between particles:
  1. Adhesion and cohesion forces in the immobile liquid films between individual primary powder particles;
  2. Interfacial forces in mobile liquid films within the granules;
  3. The formation of solid bridges after solvent evaporation;
  4. Attractive forces between solid particles;
  5. Mechanical interlocking.
Different types of mechanism were identified in each group and the ones discussed below are those that are relevant to pharmaceutical granulations.

Adhesion and cohesion forces in immobile films

If sufficient liquid is present in a powder to form a very thin and immobile layer, there will be an effective decrease in interparticulate distance and an increase in contact area between the particles. The bond strength between the particles also increased, as the van der Waals forces of attraction are proportional to the particle diameter and inversely proportional to the square of the distance of separation. This situation will arise with adsorbed moisture and accounts for the cohesion of slightly damp powders.

In dry granulation, the pressures used will increase the contact area between the adsorption layers and decrease the interparticulate distance, and this will contribute to the final granule strength.

Thin, immobile layers may also be formed by highly viscous solutions of adhesives, and so the bond strength will be greater than that produced by the mobile films. This type of film produce my starch mucilage.


Interfacial forces in mobile liquid films

During wet granulation liquid is added to the powder mix and will be distributed as films around and between the particles. Sufficient liquid is usually added to exceed that necessary for an immobile layer and to produce a mobile film. There are three states of water distribution between particles.

At low moisture levels, termed the pendular state, the particles are held together by lens-shaped rings of liquid. These cause adhesion because of the surface tension forces of the liquid/air interface and the hydrostatic suction pressure in the liquid bridge. When all the air has been displaced from between the particles the capillary state is reached, and the particles are held by capillary suction at the liquid/air interface, which is now only at the granule surface. The funicular state represents an intermediate stage between the pendular and capillary states. Moist granule tensile strength increases about three times between the pendular and the capillary state.

It may appear that the state of the powder bed is dependent upon the total moisture content of the wetted powders, but the capillary state may also be reached by decreasing the separation of the particles. In the massing process during wet granulation, continued kneading/mixing of material originally in the pendular state will densify the wet mass, decreasing the pore volume occupied by air and eventually producing the funicular or capillary state without further liquid addition.
  
Water distribution between particles of a granule during formation and drying

This will be important in the process of granulation by spray drying of a suspension. In this state, the strength of the droplet is dependent upon the surface tension of the liquid used. 

These wet bridges are only temporary structures in wet granulation because the moist granules will be dried. They are, however, a prerequisite for the formation of solid bridges formed by adhesives present in the liquid, or by materials that dissolve in the granulating liquid.

Solid bridges

These can be formed by:
  1.  partial melting
  2. hardening binders
  3. crystallization of dissolved substances.
Partial melting the pressures used in dry granulation methods may cause melting of low melting-point materials where the particles touch and high pressures are developed. The particlers will bind together and crystallization will take place when the pressure is relieved.

Hardening binders when an adhesive is included in the granulating solvent,  the liquid will form liquid bridges,  and the adhesive will harden or crystallize on drying to form solid bridges to bind the particles. 

Crystallization of dissolved substances The solvent used to mass the powder during wet granulation may partially dissolve one of the powdered ingredients. When the granules are dried, crystallization of this material will take place and the dissolved substance then acts as a hardening binder. 

The rate of drying of the granules influence the size of the crystals produced in the bridge, larger particle size will occurs if drying time longer/slower. It is therefore important that the drug does not dissolve in the granulating liquid and recrystallize, because it may adversely affect the dissolution rate.

Attractive forces between solid particles
In the absence of liquids and solid bridges formed by binding agents, there are two types of attractive force that can operate between particles in pharmaceutical systems.
Electrostatic forces may be important in causing powder cohesion and the initial formation of agglomerates, e.g. during mixing. In general they do not contribute significantly to the final strength of the granule.
Van der Waals forces, however, are about four orders of magnitude greater than electrostatic forces and contribute significantly to the strength of granules produced by dry granulation. The magnitude of these forces will increase as the distance between adjacent surfaces decreases, and in dry granulation this is achieved by using pressure to force the particles together.

Mechanical interlocking

The mechanical interlocking theory of adhesion states that good adhesion occurs only when an adhesive penetrates into the pores, holes and crevices and other irregularities of the adhered surface of a substrate, and locks mechanically to the substrate. The adhesive must not only wet the substrate, but also have the right rheological properties to penetrate pores and openings in a reasonable time.

Previous Page Next Page

People Searching On This Page:
  • granulation mechanism
  • mechanism of granulation for preparation of tablet
  • capillary state
  • mechanism of granulation
  • immoboile liquid films
  • granution mechanism
  • Granulation
  • mechanism of wet granulation
  • mechanism involved in wet granulation
  • interfacial fource in mobile liquid films
  • mechanism of wet and dry granulaton

Related Pages


Wet Granulation Process for Tablet Manufacturing

Wet Granulation Process for Tablet Manufacturing

Articles | Production
Date:
29-May-2015  Views: 4424

Know about wet granulation process including Types of Wet Granulators, Fluid Bed Dryers, Milling / Screening / Sizing, Preparation of Binder, Granule ...
Dry Granulation Process in Pharmaceutical Industry

Dry Granulation Process in Pharmaceutical Industry

Articles | Production
Date:
11-May-2015  Views: 6045

Dry granulation using Sluggers, Roller compactors. How to determine end point of granulation and problems in granulation process. ...
Process Validation : An Essential Process In Pharmaceutical Industry

Process Validation : An Essential Process In Pharmaceutical Industry

Articles | Quality Assurance
Date:
18-Mar-2013  Views: 6430

The purpose of this work is to present an introduction and general overview on process validation of pharmaceutical manufacturing process especially t ...
CO-Processing of Tablet Manufacturing Process

CO-Processing of Tablet Manufacturing Process

Articles | Pharmaceutics | Tablet
Date:
14-May-2011  Views: 3924

Co-processing is another way that new excipients are coming to market without undergoing the rigorous safety testing of a completely new chemical 19. ...
Process Validation : An Essential Process In Pharmaceutical Industry

Process Validation : An Essential Process In Pharmaceutical Industry

Articles
Date:
09-Mar-2011  Views: 6766

The purpose of this work is to present an introduction and general overview on process validation of pharmaceutical manufacturing process especially t ...
Post Your Comments (No Login Require)
Name : (required)
Email : (required)
Website :

Comment : (required)

5  + 4 =     
Comments
People Searched About:
Granulation Mechanism   |   Mechanism Of Granulation For Preparation Of Tablet   |   Capillary State   |   Mechanism Of Granulation   |   Immoboile Liquid Films   |   Granution Mechanism   |   Granulation   |  
Google : 358 times | Yahoo : 43 times | Bing : 7 times |